pocket-doors-pic1When a pocket door is off the rail, you lot will have difficulty opening and endmost information technology. Depending on the weight of the door, it may be very difficult to motion. To set this trouble the door will need to be re-attached to the hanger. The method volition vary depending on which hanger has let become.

Not sure if this is your trouble? Encounter the article on 'Fixing and Troubleshooting Pocket Doors' for a consummate listing of all the problems and the solutions for them.

Troubleshooting a Pocket Door Off the Track

Check the border of the door that is by the door jamb. Is there still a gap betwixt the corner of the door and the floor? Yes, then information technology is the back hanger that has released. If the door is on the floor at the jamb, it is the front end hanger that has let get.

Locating the Front Pocket Door Hanger

The first matter yous need to do is decide where the hanger is. If information technology is visible hanging from the guide track in the door opening, your job is much easier. Pull the hanger over into the center of the door opening.

The hanger may be inside of the pocket. Y'all will need to get a flashlight to effort and locate it. Wait in the narrow space higher up the door that goes back into the pocket. The hanger will expect like a bolt hanging downwardly below the track.

Attempt to apply a wire, screwdriver or something else to slide the hanger out into the door opening. Endeavor non to push button it any further back into the pocket. It may take a footling fleck of patience. A wire with a claw on it is probably your best bet.

If the hanger is too far back in the opening to reach you lot will have to get to plan "b". Pick up the front edge of the door off the floor a little then it does not scrape. Slide the door every bit far as you can into the opening. The back roller and hanger will push the front one out to where you can reach it. Do this carefully, you do not desire to pop the back hanger off.

When you have the front door hanger in the opening, you are ready to put the pocket door on the rail.

Locating the Back Pocket Door Hanger

When the dorsum pocket door hanger is off the track, it is a bit more of a problem. You are going to have to remove the pocket door to get the hanger out where yous tin can work on it.

Moving the door when the dorsum side is sliding on the ground is a piddling hard. Attempt holding your foot against the bottom of the door and pull gently on the top of the door to lift the back side. Work the door slowly into the opening in this fashion.

Bring the door to within a few inches of the strike side jamb. Y'all may want some help at this indicate. Someone to hold the door while you release the retention clip on the door hanger. See the article 'Removing a Pocket Door' for more information on taking the door off.

After the door is taken out and leaned against the wall, y'all will have to locate the pocket door hanger. A broom handle works well for coaxing the hanger out of the pocket.

Utilise a flashlight so that you can see what you lot are doing. With the broom handle, slide the roller carriage out into the door opening.

Putting the Pocket Door Back On the Track

When yous go put the door dorsum on the track, you desire to get the hanger on the height of the door aligned with the bolt and wheel assembly inside of the track. Putting a pocket door back on the hangers has an guild to it like most other things. There are two sides to the door, the strike side (where the lock is) and the pocket side. With a pocket door you desire to attach the hanger that is closest to the pocket side of the door.

Slide the pocket side hanger to where it is near half-dozen to viii inches from the edge of the jamb. You volition need to angle the door, so that the strike side is out of the opening. You cannot get the door into the opening until the back hanger is installed. Information technology is a good idea to accept some help at this bespeak.

There are basically two types of retention clips. One kind allows the hanger to slide sideways onto the hanger commodities. This type is more than decumbent to coming off. The other type has the hanger going straight up onto the commodities. This blazon may require that you agree the retention leap open while lifting the door. You definitely desire assist with this style.

Make certain the retentivity clip is released and adhere the prune to the back hanger. At this signal you tin can start to slide the door into the pocket. You volition have to pick up on the forepart side so that it does not drag on the floor. Be careful and adjust the angle of the door until information technology is within the opening with the front edge four to half dozen inches away from the strike side jamb.

After the back hanger is in place slide the door part mode into the pocket. Repeat the process with the front hanger. Line upward the front roller assembly with the hanger on the door. Make sure the retentiveness clip is released and attach the front hanger.

Make sure the retention clips are engaged before you start to utilise the door. Otherwise, information technology will come up off the track again.

Pocket Door Off the Track - Summary

Having your pocket door come off the rails can be a little irritating. It is all-time to have assist when you are trying to install or remove a pocket door.

Getting the roller carriages out of the pocket may have been the hardest part of this process. Hopefully, yous were able to get your pocket door working properly again.